Oxy Submersible Pool Lights - IP68 Suction Mount LED with Remote
We proudly offer complimentary shipping on every order, anywhere in Australia — no minimum spend, no surprises at checkout.
Shop with confidence knowing that if anything turns up damaged, faulty, or simply isn't what you ordered, you're completely covered — at no cost to you.
Email info@alvarahome.com with your order number and we'll take care of the rest.
We're always happy to help with any questions.
Customer service hours: Monday to Friday, 9:00am – 5:00pm AEST
Email: info@alvarahome.com
The Oxy Submersible Pool Lights are the compact end of the range: 7 cm across and 3 cm high (2.8 x 1.2 in), moulded in polycarbonate rather than ABS, which is the harder, more impact-resistant plastic and holds its clarity better against UV and pool chemicals over a season. A built-in suction cup presses them onto any smooth surface, so they mount on a pool wall, a step riser or the glass of an aquarium and stay aimed where you put them. Ten LEDs give 16 static colours plus four dynamic modes from the supplied IR remote, and the IP68 rating covers continuous submersion rather than the occasional splash. They run on three AAA batteries, so there is nothing to charge and nothing trailing into the water, and sets scale from a single light up to ten with matching controllers - enough to run a whole pool wall or line a long set of steps.
Key Features
- Polycarbonate Housing: Harder and more impact-resistant than ABS, and holds its clarity better against UV and pool chemicals.
- Suction Cup Mount: Presses onto pool walls, step risers and glass tanks so each light stays exactly where you aimed it.
- 16 Colours Plus 4 Dynamic Modes: Set a single colour or run a dynamic sequence from the included IR remote.
- IP68 Fully Submersible: Dust-tight and rated for continuous underwater use, not just splash resistance.
- Sets From 1 to 10 Lights: Scale from a single feature light up to a full pool wall, with matching controllers supplied.
Specifications & Dimensions
- Material: Polycarbonate (PC)
- Dimensions: 7 cm diameter x 3 cm high (2.8 x 1.2 in)
- LED Count: 10 LEDs per light
- Colour Options: 16 static RGB colours plus 4 dynamic modes
- Power: 2W per light
- Voltage: 4.5V per unit, 6V system
- Power Source: 3 x AAA batteries per light, not included
- Control: Wireless IR remote control, included
- Remote Range: Approximately 8 m (26 ft) in air, 1 m (3.3 ft) underwater
- Remote Battery: 1 x CR2025, not included
- Mounting: Built-in suction cup for smooth surfaces
- Waterproof Rating: IP68, rated for continuous submersion
- Certifications: CCC, CE, RoHS
- Set Options: 1, 2, 4, 6, 8 or 10 lights with matching controllers
- Recommended Use: Swimming pools, spas, ponds, aquariums, vases and party displays
Care Instructions
Release each light by easing a fingernail under the lip of the suction cup to break the vacuum rather than pulling it straight off the wall, which stretches the rubber and shortens its grip. Rinse the lights in clean fresh water after they come out of the pool: polycarbonate resists pool chemicals well, but chlorine and salt left to dry will still film the lens and perish the suction cup. Wipe with a soft cloth only - polycarbonate scratches more easily than glass, so abrasive pads and solvent or ammonia-based cleaners will craze and cloud the lens permanently. Open the battery compartment only with dry hands over a dry surface, check the seal is clean, seated and undamaged before closing it, and replace the seal if it looks flat or cracked, since that seal is the whole basis of the IP68 rating. Take the AAA batteries out whenever the lights are stored for more than a few weeks so a leaking cell cannot corrode the contacts. Store dry, out of direct sun, with the suction cups clean and not compressed.
Choose options